greetings from Australia, I have been busy getting my MB Trac finished for forest spraying. very happy with performance off road. Has anyone fitted a bowden cable to the accelerator linkage? My 130...

Thank you for the response Gerhard, I removed the tray floor today, and lifted, what I believe is the draft control mechinism? it instantly lifted the weight on the linkage with no issues. Could it ...

Greetings from Australia! I have almost finished my MB Trac 1300Turbo, I hooked the new spray unit up today and filled it with water (1000l), however the rear linkage wont lift? when empty, it lift...

Greetings from Australia, I have got my Trac 1300 Turbo on the road, but it still does not stop as well as I believe it should. Pads are good-60% life remaining, new adjusters on all wheels, system...

Hello from Australia, My 1300Turbo is nearly ready for work, with only some minor throttle issues to sort out and the brakes to re-bleed. It has been repainted, repaired front pinion, new comressor, ...

Hello Michael, The VIN is WDB 443 1630W 153650, unless the 0W is the letter o and not the number 0? Greetings, Tim

Greetings, I cant get any Mercedes truck dealers to find a data card for my 1300 Turbo. Are they available on the net or this forum? Thank you in advance, Tim

Greetings, I have pulled the entire air throttle system apart and have found the spring in the cylinder in 2 parts as per your picture. Does this affect the operation of the cylinder and the operatio...

Roby schrieb: (17.10.2017, 18:24) -- Hi Tim, It is easier to repair the existing system and keeping the Trac in original state. Here some Threads about the " Luftgas /pneumatisches Gas" https:...

Greetings from Australia, My MB Trac 1300 Turbo is very unresponsive in the throttle/accelerator control. The air valve in the pedal footwell leeks air quite a bit, and the motor wont return to id...

Greetings from Australia, My MB Trac 1300 Turbo has had the rear gaurds removed and I have no brake lights. Where does the wiring come from as I cant find where the wiring loom has been cut to rei...

Hello! I have had the front differential pinion fixed. My engineering company cut the old pinion in between the 2 bearings, oversized a new shaft, turned it down to get the right size and straightnes...

CAV schrieb: (10.07.2017, 00:19) -- Hello Everyone, Apologies as I do not speak any German, I am fro Australia. I need to fix power take off at the clutch. How do you repair the power take off clutc...

Franz Josef schrieb: (02.08.2017, 22:12) -- Hello Tim, because of your VIN we can see that your 1300 Turbo should be model year 1989. Here you can see a list of the numbers: https://www.trac...

Hello from Australia, I cant find any year model for my MB Trac 1300 turbo- one main difference I can see over other models is a digital speedometer. VIN is 4431630W 153650 Thankyou In Advance Tim

optimog schrieb: (27.07.2017, 17:29) -- Hello Tim, Crown and bevell gear is a matching set with one Number depending on the axle ratio. There is a 27/7 Ratio (A 443 330 04 39) and a 25/8 Ratio ...

Roby schrieb: (27.07.2017, 08:14) -- Hello Tim, its also possible that the Toothing from the cardan Shaft is worn out. You can check this by lifting the Front axle with four wheel and Diff.Lock e...

Hello from Australia! I have an MB Trac 1300Turbo and am getting it ready for a spraying job over our Summer. I cant get the front wheel drive to engage. I have removed the air actuator, lubricated ...