Trac 800 314 to 352a engine swap
#1
xtrac16 

Hi,

I have a MB Trac 800 with a blown engine, problem in getting a new OM314 is that I am located in Australia, and there isn't a great deal of MB engines available.

I can get an OM352a easy enough, has anyone done the conversion?

Any information would be appreciated,

Thanks.
Zitieren
#2

https://www.trac-technik.de/piwigo/index...ategory/19

Gruß Hartmut admin

MBtrac, alles andere ist Behelf!
Zitieren
#3

(21.07.2021, 10:14)Hartmut schrieb:  https://www.trac-technik.de/piwigo/index...ategory/19

Gruß Hartmut admin

Cheers thanks Hartmut.

Big job by the looks of it!
Zitieren
#4

Hi Aussie,

welcome to the greatest community of MB trac worldwide. Nice to see somebody from the other side, here. Whenever you should have problems with google translate to understand an article, do not hesitate to contact me.
And our big boss and founder Hartmut appreciates to see the name of the user.
So, enjoy the biggest MB trac cyclopedia.

BR
Tim
Zitieren
#5

Hello Evan,

a very warm welcome!

You can see: it is possible to swap the engine from OM314-4 to OM352a-6 cylinders.

We have some discussions and postings here in the community about this.

In Germany this change is normally not conform with our legal requirements. Our TÜV = technical inspection agency is very strict.

Two points of this discussions I remember:

Because the engine is longer you have to enlarge the frame or replace the tank of the hydraulic system.

The higher torque of the OM352a is perhaps critical for the gearbox.

If you want to make the change, please give us many pictures.

In the internal section Das bin Ich ...
https://www.trac-technik.de/Forum/forumd...php?fid=12
you have the posibility to tell us something about you.
It is optional!

Your questions are welcome.

Best regards
Franz-Josef
Zitieren
#6

(21.07.2021, 15:18)LLU TJ schrieb:  Hi Aussie,

welcome to the greatest community of MB trac worldwide. Nice to see somebody from the other side, here. Whenever you should have problems with google translate to understand an article, do not hesitate to contact me.
And our big boss and founder Hartmut appreciates to see the name of the user.
So, enjoy the biggest MB trac cyclopedia.

BR
Tim

Thanks Tim,

Looking forward to contribute as I build the 800.

Regards,

Evan.
Zitieren
#7

(21.07.2021, 22:24)Franz Josef schrieb:  Hello Evan,

a very warm welcome!

You can see: it is possible to swap the engine from OM314-4 to OM352a-6 cylinders.

We have some discussions and postings here in the community about this.

In Germany this change is normally not conform with our legal requirements. Our TÜV = technical inspection agency is very strict.

Two points of this discussions I remember:

Because the engine is longer you have to enlarge the frame or replace the tank of the hydraulic system.

The higher torque of the OM352a is perhaps critical for the gearbox.

If you want to make the change, please give us many pictures.

In the internal section Das bin Ich ...
https://www.trac-technik.de/Forum/forumd...php?fid=12
you have the posibility to tell us something about you.
It is optional!

Your questions are welcome.

Best regards
Franz-Josef

Hi Franz-Josef,

I will put up pictures as I proceed with repairs,

I was in the Army for many years and drove Unimogs regularly,
Hopefully the 6 cylinder and gear box get along in the 800.
I will post pictures as I go and no doubt be asking a lot of questions.

Regards,

Evan.
Zitieren
#8

G’Day Evan,

Nice to see you found your way to this community.
I lived in AU for 4 years working at the Rio Tinto smelter in Bell Bay, Tassie and saw the occasional MB trac floating around, though most of those were in terrible condition.
I believe you are located in WA? You probably should put a pin on the user map!

And yes, upload pictures. People here will appreciate getting a feel for the area you live in and the things happening at your farm.

Cheers,
Gerd.
Zitieren


Möglicherweise verwandte Themen…
Thema / Verfasser Antworten Ansichten Letzter Beitrag
Letzter Beitrag von yolko
23.07.2013, 19:04
Letzter Beitrag von Weder
07.01.2008, 12:09

Gehe zu:


Benutzer, die gerade dieses Thema anschauen: 1 Gast/Gäste